Baileigh’s largest NC hydraulic press brake weighs 8,800 lbs. with a rigid steel frame. The encoder-controlled stroke and back gauge system offers 2 DROs and takes just 5 minutes to learn. Delivers up to 90 tons of pressure. Bends sheet metal up to 78” wide. 10 hp main motor runs on 220-volt 3-phase power Runs in 3 modes: jog mode for setup, manual mode for more control over descent and return, and automatic mode for full production. 2 encoder-controlled hydraulic cylinders move the top beam. ... Read More

The JET HVBS-712 Horizontal/Vertical Metalworking Bandsaw has everything any operator needs to tackle even the toughest job. JET increased the width and height of the stand and added new features that exceed expectations. The HVBS-712 is another innovative JET product packed with features you’ve come to expect. FEATURES 9″ x 12″” work table in the vertical position Rapid action vise miters to 45° Improved Height and width of stand with built-in storage cabinet and chip tray Adjustable material stop for repeatability CSA/CUS : Following strict guidelines and electrical requirements, this JET Saw is CSA/CUS certified Blade drive is a belt to sealed, hardened and ground gear drive system... Read More

JET Dual Mitering Horizontal bandsaws unique design head dual miters both left and right for quick angle cuts. FEATURES Heavy duty construction reduces vibration and deflection Built in, self propelled blade brush prevents chip build up in blade guides Blade tension gauge helps to ensure the blade is in the correct cutting position Magnetic starter for low voltage and lost phase protection Automatic blade breakage sensor detects accidental breakage and interrupts the power Power switch with safety key provents accidental start up CSA/CUS: Following strict guidelines and electrical requirements, this JET saw is CSA/CUS certifield Blade is fully guarded for Operator safety Automa... Read More

Smaller shops and job sites alike benefit from the power and precision of JET when the HVBS-56M is put into action. Its 1/2HP motor offers great versatility and power when cutting in either a horizontal or vertical position. Long list of features and JET backed Two Year Warranty make this saw a must have for your operation. ... Read More

Used Promaster Pro28 3X5 radial arm drill press. 2 HP, 3 PH, 230 volt, 1700 RPM. It has six spindle speeds, 88, 154, 282,455,796, and 1500, as well as three feed steps. It can drill up to 1-1/2″, and tap up to 7/8″ in mild steel. It features power downfeed, as well as power to raise and lower the arm. The machine is currently up to power and in excellent working condition.

The Edwards 40 ton ironworker is the perfect addition to your home, farm, or small fabrication shop. It comes standard with a roundpunch capable of 1″holes in 1/2″ steel, a flat bar shear, and a angle shear. It also has a fourth open tooling station that can be customized to your needs with the eleven interchangable attachments and the accessories available. Specs: Four Workstations Open Tooling Station Operates on 115V Power Integrated Lock-out/Tag-out Made to order, three week lead time, price can vary depending on tooling.

Edwards 25 ton dual station power link hydraulic ironworker. Features: Two Workstations 9 Available Attachments 7 Optional Acessories Electric Foot Pedal w/ Integraded Jog Control 20 Foot Quick-Connect Hose REQUIREMENTS! Edwards Ironworker with PowerLink System, or Portable Power Unit

Grob vertical metal cutting bandsaw. Model NS-18 1HP, 3PH, 220/440 Volt Built in Blade Welder Work Light 24″ x 24″ Table Approximately 1500 pounds

The BDB-919 benchtop lathe is perfect for the most versatile shops. Engineered with precision induction hardened ground bed-ways and precision tapered roller bearings, the BDB-919 delivers the smooth operation and rigidity needed to craft professional pieces. Backlash adjustments provided throughout the carriage Emergency stop within easy reach of the Operator Full Length Splash Guard Power longitudinal feed allows threading and reverse threading Quick change gearbox provides wide range of inch and metric threads Reversing switch for added versatility Safety on/off switch Some images show lathe with optional stand Standard Accessories Specifications More Information Stock Number JT9-321378 Carriage Travel (In.) 17.5 Compound Slide Travel... Read More

With features unmatched, the JET Dual Mitering , Semi-Automatic, EVS Bandsaw is the perfect solution for cutting structural steel with ease. FEATURES Electronic variable speed from 50-297 SFPM Heavy duty construction reduces vibration and deflection Hydraulic assist descent control Auto table swivel Blade tension gauge helps to ensure the blade is in the correct cutting position Semi-auto on saw bow lifting and hydraulic vise Swing away control box allows Operator to use in any position SPECIFICATIONS Throat Depth (In.)18 Blade Speeds Metal (SFPM)50.3 Blade Speeds (SFPM)50 – 300 Round at 45 Degrees (In.)18 Round at 60 Degrees (In.)18 Round at... Read More

This rugged hydraulic ironworker machine amps up the efficient, feature-loaded design of our SW-50 models with additional capacity for tougher applications. If your shop takes on punching, shearing, and notching jobs on a regular basis, let the SW-623 prove how hardworking a hydraulic ironworker can be over decades of use. Runs on 220-volt 3-phase power. Delivers a robust 62 tons of pressure at all 5 integrated stations: punching, flat bar shearing, angle shearing, bar shearing, and rectangle notching. Pure vertical hydraulic movement at each station produces exceptionally clean cuts, notches, and holes in seconds. You can set the backgauge and material stops to save time and ensure repeatability for production r... Read More

Looking to increase productivity in your shop? This hydraulic ironworker enables 2 operators to work independently at any of the machine’s 5 stations. Plus, the machine’s pure vertical movement minimizes distortion and delivers clean cuts every time. SW-95 universal ironworker runs on 220-volt 3-phase power. 95 tons of punching pressure and a whopping 123 tons of shearing and notching force. 5 integrated workstations each execute a different function: punching, notching, flat bar shearing, angle shearing, and bar shearing. Dual-operator design enables 2 people to work at opposite ends of the machine simultaneously without loss of power at either station. Hydraulic cylinders use entirely vertical movemen... Read More

Punching. Shearing. Notching. Sounds like work for 3 machines, doesn’t it? But you can do it all with just one: the SW-503 hydraulic ironworker. This machine was manufactured to multitask at your shop for decades. This 50 ton ironworker runs on 220-volt 3-phase power. 50 tons of vertical pressure at each of its 5 integrated stations. 5 workstations each execute a different function: punching, flat bar shearing, angle shearing, bar shearing, and rectangle notching. Vertical hydraulic movement executes clean cuts in seconds, prevents deformed edges, and reduces waste. Material stops and multipositional backgauge simplify production runs. Large 2-piece tables with meter guides pull out from the machine... Read More

The Edwards 40 Ton ironworker features 40 Tons on 115 Volts with Four Available Workstations Standard (3) – Punch, Flat Bar Shear & Angle Shear Open (1) – Factory installed 8” Brake Includes an 8″ Brake with 4-Way Die allowing 1/16″, 1/8″, 3/16″ and 1/4″ material to be formed to a 90° angle 11 interchangeable Attachments available 16 optional Accessories available Operates on 115V power ANSI B11.5-1988(02) Compliant Guarding ETL Certified Controls Integrated Lock-out/Tag-out system with E-Stop for added safety This 40 Ton C Ironworker is perfect for everything from a home garage or farm to a medium size workshop including a fact... Read More

Another JET combination Bench Belt and Disc Sander designed to deliver the superior finish. The design of this machine permits sanding, grinding and finishing of outside curves or odd-shaped pieces. Heavy-duty base, cast construction and cast iron tilting table means you are getting the very best JET has to offer. Abrasive belt unit removes material and finishes at the same time, allowing the operator to get into small openings, plus handle odd shapes and angles Adjustable dust deflector and dust chute Allows for sanding,... Read More

Used Roper Whitney rotary machine in great conditon. Power is manual and it comes with a 3/16″ bead setup. In #200054

DESCRIPTION This new JET GH-1440B Geared Head Bench Lathe is engineered for smooth, quiet operation and user versatility. Positioned on a heavy-duty stand with a newly added built-in footbrake, the GH-1440B includes precision induction hardened ground bed-ways, spindle roller bearings, and high-quality steel hardened gears in the headstock for ultimate working durability. The GH1440B also includes a patented electronic chuck key docking station that prevents startup without the chuck key when safely docked. FEATURES Precision spindle roller bearings High quality steel hardened gears in headstock Lead screw cover Cast iron Stand Foot Brake comes standard Emergency Stop within easy reach of ... Read More

# 200055 New old stock of Letter Brakes. Perfect for sign applications or small aluminum flashings. Eight inch working width with adjustable toggle clamp for tension.There are two mounting holes on either side to easily mount is to a workbench or stand.

This variable-speed drill press runs smoothly even at full capacity—and will do so for years at your shop. Unlike pulley-driven drills, this 16″ drill press lets you run tooling at the proper speed to fit your application and extend tooling life.   2 hp motor requires 220-volt single-phase power and will work at virtually any shop or site. Inverter-driven head drills a maximum capacity of 1” steel. You can fine-tune the speed in the range from 150 to 3000 rpm to suit your application. Auto-reversing tap has a tapping ... Read More

Used Colchester Mascot 1600 engine lathe in great condition. 10HP, 3PH, 440 volt,with a 18″ swing with 100″ between centers. It will come with a 12-1/2″ 3 jaw chuck, a 16″ four jaw chuck, a steady rest, and several dead/live centers. It also has a coolant pump, and a taper attachment. Overall great condition, just out of a working shop.

Baileigh Tubing Die DS-1250, P-R300. New in good conditon ID #200002

Used Diacro 12 inch hand operated slip rolls in excellent conditon. Model is GA-1548 and its capacity is 20 gauge in soft steel.

Need high production in a limited space? This CNC hydraulic press brake offers programmable controls, top-quality components, and heavy steel construction for an unbeatable price. BP-3305CNC delivers 33 tons of pressure across its 63” table. Runs on 220-volt 3-phase power. Easy-to-use programmable 2-axis Estun E21 controller is integrated right from the factory. Internal memory can hold 40 programs, each with its own unique number for easy identification. Controller will keep a piece count for large production runs. Made with NOK, Siemens, and Omron components. Foot pedal lets you control all bending functions, whether on full auto or jog mode. Fully welded steel plate frame minimizes de... Read More

The Jet ELITE line of saws is a top line designed for the industrial manufacturing industries, where strict tolerances, durability, and safety are a must. FEATURES Adjustable Material Stop Automatic blade shut off switch stops the sawing process Built-in, self-propelled chip brush prevents chip build up in blade guides. Dual mitering allows for compound angle cutting of 60° right and 45° left Heavy-duty construction reduces vibration and deflection Integrated pressurized wash hose for easy machine cleaning Large handwheel with blade tensioning gauge acurately measures blade pressure Quick positioning vise for clamping of materials Semi-automatic bow raises after cut to prede... Read More

Our PT-105HD has the structural strength to handle 5’ x 10’ sheets. Automatic height detection is ideal for production runs. It arrives nearly fully assembled and comes with software. Runs on 220-volt single-phase power. Control the X, Y, and Z axis movement from the sturdy podium with large console screen and keypad. Includes easy-to-learn design software that you can load into any basic PC (more details below). Console offers a pre-loaded library of shapes that you can resize and alter at the table—without a computer. Automatic height detection on the Z-axis makes perfect cuts in corrugated or uneven materials. Panasonic® brushless servo motors, controlled by Panasonic® servo motion controll... Read More

The Edwards 55 Ton Ironworker is a best selling model, featureing four workstations Standard (3) – Punch, Flat Bar Shear & Angle Shear Open (1) – Factory installed 10” Brake Includes a factory-installed 10″ Brake with 4-Way Die allowing 1/16″, 1/8″, 3/16″ and 1/4″ material to be formed to a 90° angle 12 interchangeable Attachments available 17 optional Accessories available ANSI B11.5-1988(02) Compliant Guarding ETL Certified Controls Integrated Lock-out/Tag-out system with E-Stop for added safety The Edwards 55 Ton Ironworker is well suited to fit the needs of any fab shop, large or small. Standard features include a Punch Assembly wi... Read More

High-speed precision and amazing versatility. This rugged piece of equipment has a belt that operates at any angle, and conforms to curves, angles or circular finishing and grinding operations. Machinists who take great pride in their work prefer the JET Industrial Combination Belt & Disc Finishing Machine 0 grit belt and disc standard on machine Adjustable dust collector and dust chute Belt head adjusts vertically and horizontally Belt operates at any angle ... Read More

From the home welding shop to full production environments, the need to fixture projects on a flat surface is paramount. Baileigh Industrial’s line of U WELD welding tables and accessories are the perfect balance of quality and affordability to meet that need . Table tops and sides are made from think 4 gauge plate steel and include 16mm fixturing holes. A weld together interlocking design with full cross brace structure underneath ensure these tables will remain flat under high temperatures. Also, over 10 different accessories and a full fixturing clamp kit are available. This quality table and multiple accessory combination at an affordable price make it the perfect setup for someone new to the trade or the seasoned veteran. ... Read More

Powermatic 10″ Table saw, with Porter Cable Router & Lift Model: 66 Serial: 98662110 3HP, 1PH, 230V Baldor Motor Porter Cable 1-1/4HP Router & Lift Magnetic Contactor Start/Stop 50″ Extension Board and Rails USA Made in TN Includes all the wrenches, as well as a new saw arbor

Paul saw by Koch Machinery CNC optimizing upcut saw. Program the machine to the length desired, and it will remove the defects,cut to length, and push the parts by the length/offcut to the side to be stacked. Power requirement is three phase, 440 volt 125 PSI This machine is ideal for flooring production, and industrial applications where a large volume of same size parts are needed If machine is running at optimal performance, it will need three guys running non-stop to keep up. Contact us for more information

Extrema offers a full range of wide belt sanders that were designed in the USA especially for the American market. All of our sanders are built using the highest quality components and construction methods such as mono-block construction, electrical controls, and Camozzi pneumatics. Excess Series Excess Series wide belt sanders use a 60″ belt. Theses machines have the same quality construction as our larger machines, but are affordable enough for even the smaller manufacturers. Truly an “excessive” amount of features for sander in its class. Horsepower: 20HP Voltage: 230V or 460V Phase(s): 3PH Belt Size: 37″ x 60″ CFM Requirement: 1800 Main Motor: 20 HP Feed Motor:... Read More

Shipping: $425.00 The SawStop® Industrial Cabinet Saw is the definition of industrial grade. It is the heaviest, most powerful and highest quality 10″ cabinet saw available. The 5HP, 3ph, 230v configuration with a 36″ Industrial T-Glide Fence Assembly offers the durability, versatility, and the peace of mind only SawStop’s patented safety system can provide. 36″ Rip Capacity: 5HP, 3PH, 230V  

Shipping: $325.00 The Professional Cabinet Saw is SawStop’s top selling cabinet saw, offering unmatched fit and finish and best-in class cutting performance. 52-INCH T-GLIDE FENCE ASSEMBLY: The 52-inch T-Glide Fence & Rail are made of heavy-gauge steel for sure lockdown and reliably square cutting for years without deflection. UNMATCHED QUALITY: The trunnion and arbor are built for precision, strength and stability. The gas piston elevation delivers smooth and easy adjustability. Table flatness is measured diagonally at 0. 010” maximum gap. DUST COLLECTION: 99% dust collection is delivered above the table with the included dust collection blade guar... Read More

Shipping: $425.00 The SawStop® Industrial Cabinet Saw is the definition of industrial grade. It is the heaviest, most powerful and highest quality 10″ cabinet saw available. The 7.5HP, 3ph, 230v configuration with a 52″ Industrial T-Glide Fence Assembly offers the durability, versatility, and the peace of mind only SawStop’s patented safety system can provide.

New Jet 20″ Shaper Jet stepped up their previous shaper model with a more robust design that includes more speed and durability. Introducing the JET JWS-20CS, 20-Inch Shaper (724020). With 12.5% more spindle speed (at 8,000-10,00 RPM), this reengineered solution guarantees to take your shop to the next level. Its compact, versatile design is perfect for shops where space is premium; however, we sacrificed no power with our well-known and highly reliable 1.5-HP motor woodworking enthusiasts have come to love. COMPACT Compact footprint to add value in... Read More

Shipping: $325.00 The Professional Cabinet Saw is SawStop’s top selling cabinet saw, offering unmatched fit and finish and best-in class cutting performance. 52-INCH T-GLIDE FENCE ASSEMBLY: The 52-inch T-Glide Fence & Rail are made of heavy-gauge steel for sure lockdown and reliably square cutting for years without deflection. UNMATCHED QUALITY: The trunnion and arbor are built for precision, strength and stability. The gas piston elevation delivers smooth and easy adjustability. Table flatness is measured diagonally at 0. 010” maximum gap. DUST COLLECTION: 99% dust collection is delivered above the table with the included dust collection blade guar... Read More

Shipping: $75.00 The SawStop Compact Table Saw features SawStop’s patented safety system with the mobility you need to work from anywhere – at home or on the job site. With a 10″ blade and durable construction, you’ll have the power and accuracy you need. SPECIFICATIONS Motor Configuration120 VAC 60 Hz, Universal Amperage (A)15A No-Load RPM4,000 ... Read More

If you need a heavy duty industiral planer, look no further than the Powermatic WP2510 Planer. It has a solid steel helical cutterhead with 174 four-sided carbide knife inserts that require no adjustments when changing. With a digital readout and simple PC controller, setting up table heights is quick and easy. The frame is machined from heavy cast iron and has extra wide side panels that offer rigid bed support and ensure accurate alignment. The planer’s segmented, serrated infeed roll with segmented chip breakers has an independent yield of 1/4. Its automatically adjusting, chain drive gear box powers the 3″ diameter infeed rollers, solid pressure bar and dual outfeed rollers for precise feeding of stock. The 3-speed feed selector ... Read More

The Powermatic 201HH 20″ helical head planer is a excellent addition to any production woodshop. This 1,300-pound heavy duty cast iron planer offers rock solid rigidity and accurate planing for years to come. The hinged top allows easy access to the rollers and knives, and has a 5” dust port for easy attachment to any dust collection system. The cutterhead is a helical design with 125 four sided knife inserts – these produce a superior finish and much quieter operation compared to conventional cutterheads, and the inserts are installed without further adjustments. The anti-kickback fingers and pressure bar are located in close proximity to the cutterhead for an exceptional finish. Infeed and outfeed rollers are fitted with roller b... Read More

The Jet 6″X 89″ oscillating edge sander is a exceptional machine with the power for large jobs and the ablility to face, edge, and contour sand, all in one unit. Features: Oscillating Belt Graphite Platen Cast Iron Table 4″ Dust Port Tilting Sanding Head Specs: Style (Type) Floor Sanding Belt Size 6″ X 89″ Main Table Size 29-3/4 x 9-7/8 Main Table Tilt (Deg.)90 Dust Port Outside Diameter (In.) 4 Motor Power (HP) 1-1/2 Motor Phase 1 Motor Voltage 115V Prewired Voltage 115V

The Powermatic PM23130K is based off the Powermatic 2000B series of saws which are similar to the old 66 series units. It offers outstanding features such as oversized cast iron tables, an arbor lock, which eliminates the need for dual wrenches, and a quick release riving knife. Features: One-piece cast iron box trunion Integrated digital readout Integrated hydraulic castor system Arbor lock for quick blade change Cast iron table tops Quick release riving knife Integrated dust collection Specs: Style (Type) Cabinet Blade Diameter (In.) 10 Arbor Diameter (In.) 5/8 Arbor Speed (RPM) 4500 Maximum Depth of Cut at 90 Degrees (In.) 3-1/8 Maximum Depth o... Read More

The Powermatic PM23150K is based off the Powermatic 2000B series of saws which are similar to the old 66 series units. It offers outstanding features such as oversized cast iron tables, an arbor lock, which eliminates the need for dual wrenches, and a quick release riving knife. Features: One-piece cast iron box trunion Integrated digital readout Integrated hydraulic castor system Arbor lock for quick blade change Cast iron table tops Quick release riving knife Integrated dust collection Specs: Style (Type) Cabinet Blade Diameter (In.) 10 Arbor Diameter (In.) 5/8 Arbor Speed (RPM) 4500 Maximum Depth of Cut at 90 Degrees (In.) 3-1/8 Maximum Depth o... Read More

The Kreg DK1100 FE is an industry standard when it comes to drilling pocket holes. Sold with a electric motor, it will bring productivity and efficiency to any shop. Features: Electric 110 volt motor Convenient swing stops Adjustable fence Quick-change drill bits Long lasting motors Specs: Motor 11/2″-HP, 110-volt, single-phase Drill Bits DKDB Drill Bit 3/8″ shank diameter 3/16″ pilot 1/2″-long CFM Rating 1 CFM clamp cylinder (90 PSI/minute) Cycle Time 1 second Material Clamping Capacity 4″ Hole-Centering Capability 1/2″- to 11/2″-thick Weight... Read More

The award winning PM2000B table saw sets a new standard for innovation with an array of patented features and massive body design. The cast iron tables are oversized, and the newly designed arbor lock lever is accessible from above the table top to eliminate the need for dual arbor wrenches. The quick-release riving knife design helps reduce the chance of kickback. The blade tilt scale features an integrated digital read out as well as adjustable angle indicators for repetitive bevel cuts. The newly designed integrated retractable hydraulic caster system mobilizes your table saw much higher than the previous model to assist when moving over thresholds. A wide stance, heavy-duty box trunnion and concave teeth on the trunnion gears promote... Read More

The Extrema XR-20 has a 14″ to 20″ saw blade capacity, making the ultimate machine for large heavy timber ripping. It features a garanteed 13 foot glue line, 20 HP main motor, optional digital readout, optional black max laser, and heat-treated cast steel chain. Features: 14″ to 20″ blade capacity 20 HP motor Automatic chain lubrication Variable feed speed (50-180 fpm) Rack and pinion fence Quality electrical and pneumatic controls Disc brakes Triple anti-kickback finger 5-1/8″ Maximum thickness Bottom mounted blade for stability 12 Hold-down rollers 8-1/2″ Wide Chain pads Motorized elevation Specs: Horsepower: 20HP Voltage... Read More

The Model LM116 is Uniquely Designed to quickly and easily produce a lock miter joint for face-frame cabinetry, beams, pillar and column wrapping, box newel posts, solid surface, and more! A and B profiles are cut using a Single Pneumatic Powered Tilting Spindle Features: Increase in efficiency Less downtime switching shaper profiles Less glue up and clamping time Capabilities: 1″ Max material thickness 1/2″ Minimum material thickness 1-1/4″ Minimum material width 2″ Minimum material width(2 Sided) 12″ Minimum material length Can machine material finish angles from 90 to 30 degrees Specs 5HP Spindle Motor(Hydraulic configura... Read More

MODEL M312 Mount-A-Glide Easy Controls + Easy Setup + Easy Drilling = Easy Drawer Notching! Our Model M312 is Designed to Produce an EASY, FAST, and ACCURATE drawer box notch with a drilled locating hole simultaneously! This upgraded model includes EASY Foot Cycle Switch!!! Under mount notched and locating hole drilled simultaneously! EASY drawer locating regardless of box width using center stop! LOW MAINTENANCE machine for a GREAT VALUE! APPLICATION SPECIFICATIONS: Notch Dimension: 35mm W x 1/2″ H Locating Hole Diameter: 6mm Operating Performance: Over 200 boxes per hour DRIVE PACKAGE SPECIFICATIONS: Main Motor: 1.5 HP Pneumatic Drill Included 8&#... Read More

Shipping: $200.00 The SawStop(R) Jobsite Saw Pro delivers durability, innovation and precision with a design that’s built for the worksite. The JSS Pro has the following features: SAWSTOP’S PATENTED SAFETY SYSTEM: Stops a spinning blade on contact with skin. The blade stops in less than 5 milliseconds, and drops below the table, minimizing a potentially life-altering injury to a mere scratch. CLASS-LEADING FEATURES: 24 5/8” table depth allows a larger surface to make safe and accurate cuts from. Included Active Dust Collection Guard for class-leading dust management. One-turn elevation allows the user to raise and lower the blade in a single turn, and the Qu... Read More

Shipping: $325.00 The Professional Cabinet Saw is SawStop’s top selling cabinet saw, offering unmatched fit and finish and best-in class cutting performance. 36-INCH PREMIUM FENCE ASSEMBLY: This aluminum fence assembly provides smooth operation and precise measurement UNMATCHED QUALITY: The trunnion and arbor are built for precision, strength and stability. The gas piston elevation delivers smooth and easy adjustability. Table flatness is measured diagonally at 0.010” maximum gap. DUST COLLECTION: 99% dust collection is delivered above the table with the available dust collection blade guard and below the table with advanced shrouding around the blade. ... Read More

Shipping: $325.00 The Professional Cabinet Saw is SawStop’s top selling cabinet saw, offering unmatched fit and finish and best-in class cutting performance. 30-INCH T-GLIDE FENCE ASSEMBLY: The 30-inch T-Glide Fence & Rail are made of heavy-gauge steel for sure lockdown and reliably square cutting for years without deflection. UNMATCHED QUALITY: The trunnion and arbor are built for precision, strength and stability. The gas piston elevation delivers smooth and easy adjustability. Table flatness is measured diagonally at 0. 010” maximum gap. DUST COLLECTION: 99% dust collection is delivered above the table with the included dust collection blade guar... Read More

The POWERMATIC® 43″ Wide Belt Sander delivers the utmost performance in measurement and sanding, creating a flawless finish every time. The Sander has centralized controls which allow the user to access all the needed buttons on one simple panel for more convenience. The variable speed feed belt allows the user to accurately dial in the exact feed speed to best suit each project and work environment. The sander also features a special digital readout control. This element is especially helpful because it will show the exact thickness of the finished piece or will allow the user to preset exactly what thickness they would prefer the finished piece to be. The sander also includes a unique measuring device, the auto thicknesser, that wil... Read More

Shipping: $425.00 The SawStop® Industrial Cabinet Saw is the definition of industrial grade. It is the heaviest, most powerful and highest quality 10″ cabinet saw available. The 7.5HP, 3ph, 230v configuration with a 36″ Industrial T-Glide Fence Assembly offers the durability, versatility, and the peace of mind only SawStop’s patented safety system can provide. FEATURES 36″ Industrial T-Glide Fence System provides smooth operation, precision measurement and sure lockdown without deflection. Durable craftmanship and thoughtful details combine for consistent, reliable perfor... Read More

Used Konig German made wood lathe. Aporoximately 14″ swing with 40″ between the centers. All steel and cast construction, 115 volt with a 3/4HP motor. 3/4 HP, 1PH 115V 380 to 3200 RPM Large 14″ Swing 1″-8 Spindle MT2 Headstock/Tailstock Includes: 10″ Tool Rest 12″ Tool Rest 31″ Tool Rest Curved Tool rest for Bowls Spur Drive Screw Chuck 6″ Face Plate Live Center Machine has been cleaned and checked, and ready to work. Located and sold by Blue Ball Machine Co Inc

Up for sale is a Clean Delta USA made 10″ table saw, with 52″ Delta Unifence and Uniguard Dust Collection Model: 36-812 Serial: 1162241 10′ Blade Capacity 5HP, 3PH, 230V Features Deltas trademarked aluminum two way Unifence and Uniguard overarm dust collection

Take A Look At This Very Clean Omga RN600 14″ Radial Arm Saw! This machine is a 2001 year but you would hardly know it! Everything works as it should, and it is in excellent running and operating condition. The missing front rail cap has been replaced as well. The precision of these radial arm saws is identified by the following characteristics: Saw carriage slides on 8 bearings, having dust scrapers which guarantees complete cleanliness of both the interchangeable steel tracks and the bearing. Self-centering locking in the main angles position of the arm, the motor and the carriage with the possibility of manual locking at all intermediate angles. Easy and extremely practical unlocking of the arm rotation on the front. Swiveling and t... Read More

Northfield is the standard when it comes to heavy duty woodworking machinery, and are one of the few businesses manufacturing in the USA. This  16″ Heavy Duty Jointer is a testament to their legacy. Model: 16HD Serial: 591321-F Length of Knives: 16″ Knife Size: 16″x1-1/4″x1/8″ 3 Knife Cutterhead, Belt Drive, Approx 4500RPM 4-1/4″ Cutting Circle 96″ Long Tables 5-1/2″x52″ Cast Iron Fence Fence tilts to 45 Degrees 5/8″ Maximum Rabbet Depth 5HP, 3PH, 208/230/440V 1825lbs 38″x96″ Floor Space          

Shipping: $325.00 The Professional Cabinet Saw is SawStop’s top selling cabinet saw, offering unmatched fit and finish and best-in class cutting performance. 36-INCH T-GLIDE FENCE ASSEMBLY: The 36-inch T-Glide Fence & Rail are made of heavy-gauge steel for sure lockdown and reliably square cutting for years without deflection. UNMATCHED QUALITY: The trunnion and arbor are built for precision, strength and stability. The gas piston elevation delivers smooth and easy adjustability. Table flatness is measured diagonally at 0.010” maximum gap. DUST COLLECTION: 99% dust collection is delivered above the table with the available dust collection blade guar... Read More

The 14BX Series of straightline rip saws lead the way in innovation and value for for medium to large size woodworking facilities. With the bottom blade cutting design, they are among the safest in the industry. With the full heat-treated cast-steel chain and race, they are unmatched in durability. 15 HP Main motor Huge 45″ x 61″ table available 6 full hold down rollers Variable feed speeds from 50-120 ft/min 8′ Guaranteed Glue Line Disc Brakes Micro adjust fence with handwheel Triple anti-kickback fingers 18″ wide ripping capacity Automatic Oiler with low-oil warning Wye-Delta soft start Heat treated chain and race Amp meter Square D Electrical ... Read More

The TALENT T5D 510 is a high-performance nesting CNC router offering speeds and specifications not found in other machines in this price offering. It is a three axis, panel-processing machine tool capable of cutting a wide range of materials including wood products, plastics, and non-ferrous metals. The Talent T5 is used extensively in cabinetmaking, closet manufacturing, sign-making, and plastics fabrication. This CNC Router utilizes industry leading components, such as 1.5 KW servo motors, a 16-horsepower spindle, and Delta CNC controls. Rapid speeds of 100 meters/min. (3,937 inches per minute), standard 12 position carousel tool changer, 10-position boring block, 16 horsepower spindle, panel sweep, automatic panel alignment, and pre-c... Read More

SCMI R9 Overarm pin router. It was pulled from service and is ready to run. Model: R9 Serial: AA50584 10HP, 3PH, 230V 2 Speed Spindle, 10K and 20K Handwheel Table Elevation Pneumatic Spindle Activation Phenolic guide Fence

The DK1100 series of machines are the standard in the industry for drilling a single pocket hole at a time. We’ve packed a ton of functional features into these machines that set them apart from the competition. Choose from electric- or pneumatic-powered, freestanding or bench-mounted to fit the way you build. Each DK1100 machine is built with industrial-grade motors that provide the power to run day after day – quickly, quietly, and reliably – in even the most high-production environments. For most shops, this translates into previously unheard of productivity and efficiency. This model is identical to the DK1100 FP, but comes in a much smaller frame. It features a table height of 8″, making it easy to build int... Read More

EASY Coping Machine C117 Details APPLICATION SPECIFICATIONS: EASY Quick-Change Spindle INCLUDED EASY Foot Pedal Cycle Start EASY Backer Block Change EASY Pneumatic Hold Down Clamp System 16” Wide Cutting Capacity 5/8” to 1” Material Thickness DRIVE PACKAGE SPECIFICATIONS: Main Motor: 5 H.P. 1.25” Spindle 4” Diameter Cutter Compatible Available in 220v 3ph, 460v 3ph, and Hydraulic Drive Packages (some electric needed for readouts) Flat Belt Drive Y and Z Axis Spindle Adjustment with DRO UTILITY REQUIREMENTS Dust Collection Requirements: 670 CFM, 4″ Outlet Pneumatic Requirements: 90-100 PSI to Power Table and Clamp 25 ... Read More

EASY Coping Machine C220 Specifications APPLICATION SPECIFICATIONS: EASY Quick-Change Spindles INCLUDED EASY Foot Pedal Cycle Start EASY Pneumatic Hold Down Clamp System 16” Wide Cutting Capacity 5/8” to 1” Material Thickness DRIVE PACKAGE SPECIFICATIONS: Main Motors: 2 – 5 H.P. 1.25” Spindles 3” and 4” (ID) Cutter Compatible Available in 220v 3ph, 460v 3ph, and Hydraulic Drive Packages (some electric needed for readouts) Flat Belt Drive Y and Z Axis Spindle Adjustments with DRO UTILITY REQUIREMENTS Dust Collection Requirements: 2 – 4″ Outlets, 670 CFM (each) Pneumatic Requirements: .3 CFM @ 100 PSI to Power Table and Clamp... Read More

The 8″ Parallelogram Jointer offers performance and value in a machine loaded with features. The cutterhead is a helical design with 54 four sided knife inserts – these produce a superior finish and much quieter operation than conventional cutterheads, and the inserts do not require adjustment once installed. The Jointer has an extra long 82” bed for better work support and is equipped with an innovative single handwheel design that tilts the fence in and out with positive stops at +/-45 and 90 degrees. A non-mar insert in the fence contacts the table to avoid scratching the surface during adjustments. The parallelogram design keeps the table in close proximity to the cutterhead for improved finish and allows for a fast depth o... Read More

This 8″ Jointer meets the demand for accuracy while combining unique, user-friendly functions. The infeed table lever can be used to rapidly position table height, then the handle rotated for fine-adjustment of cut depth. Fence tilting is accomplished by a worm gear system, smoothly operated by a simple handwheel. The tables provide 73” long extended support. A non-mar insert in the fence protects the table from scratches during adjustments. The jointer is available with a three high speed steel knife cutterhead, or a helical cutterhead with 54 four-sided knife inserts. The operating switch is high mounted for easy reach, and the push blocks have a magnetic base – store them on any metallic surface for instant access. ... Read More

Take a look at this C.O. Porter Surfacemaster 715 facing planer! An underrated machine for flattening and prepping lumber for surfacing Model 715A Serial: 6212 15HP, 3PH, 230/460V 3/4HP Elevation Motor Chain Driven Carpet Feed 24″ Wide Cutterhead with Dispozablade Knives(Comes with ITCH head as a alternate option) 8″ Max Thickness Capacity Power Elevation Wixey Thickness DRO Spike Infeed Magnetic Start/Stop 6″ Dust Port Weight is approx 6500lbs This surfacer is a beast, and will operate with very little vibration due to its large cast iron frame. These machines are known to make chips, and are excellent for prepping or surfacing lumber. Mach... Read More

Designed for continuous, industrial use, the Extrema ET-150 is excellent for demanding applications. Features: Large table Spindle lock and brake Emergency Stop Spindle speeds of 5.5K, 7.5K, and 10K RPM Magnetic Starter Micro adjust left and right Optional Digital Readout Specs: Horsepower: 7.5HP Voltage: 230V or 460V Phase(s): 3PH Main Motor: 7.5 HP Spindle RPMs: 5.5 / 7.5 / 10K CFM Requirements: 750 Table Size: 46″ x 34″ Max Diameter: 12-3/8″ Spindle Travel: 6-1/2″ Included Spindles: 1-1/4 Fixed 1-1/4″ Spindle: 5-13/16″ Interchangeable Spindles: No Amps: 18 We... Read More

Professional grade pocket hole machine at a affordable price. Features include: One pull of the handle starts the motor, clamps your workpiece, and drills perfect pocket holes 110-volt motor 3/8″ hex-shank drill bit (QUIK-BIT) Adjustable fence Two spring-loaded stops Specs: Motor: 110-volt Drill Bits: Comes with standard Kreg 3/8″ (9mm) stepped drill bit Also accepts Kreg Micro-Pocket™ and HD drill bits Material: Polyurethane base; cast-aluminum tabletop Clamping Capacity: Material from 1/2″ to 11/2″ thick (13-38mm) Weight: 20 lbs. Dimensions: Entire Unit: 15″H x 19″L x 29.5″D (380mm x 482mm x 750m... Read More

The Extrema XS-2P43 is a heavy duty wide belt sander that falls in the middle of their industrial line of wide belt sanders. It offers high quality components such as mono-block construction, Telemecaique electrical controls, and Camozzi pneumatic’s. Features: 4 Post Table 75″ Belt Length Over thickness safety device Infeed bed rollers Digital thickness controller Individual amp meters Disc brakes on sanding heads Telemecaique electrics Camozzi pneumatics Variable speed drive system Specs: Horsepower: 30/25HP Voltage: 230V or 460V Phase(s): 3PH Belt Size: 43″ x 75″ CFM Requirement: 4200 Main Motor: 30 / 25 HP Feed ... Read More

Good used hinge boring machine,manufactured in Austria. It is powered by a 1HP motor, single phase, 220 volt motor. It has pneumatic clamping and A 53″ fence system both left and right from the center of the machine. In ID. 100026

Brand new variable speed sander. It has the capabilities for contour and straight finishing aplications. 1HP single phase motor, 115,or 230 volt, with a varible frequency drive. The brush head and pneumatic drum are sold seperately and available in different sizes and grits.

Used Grass Imperial 1241 hinge boring machine. It is electric and pneumatic operation with a Dayton 1 HP 3 PH motor, 220 or 440 volt, and pneumatic cycling and hold downs. It has 5 spindles, 42 mm on centers, It comes with 3 foot rails,left and right, as well as several boring bits and all the manuals. Excellent condition, well maintained machine.

NEW ITEM! Shop Fox W1833 pocket hole machine. 1/2 horsepower, single phase, 120 volt, with a spindle speed of 2500 RPM. It is capable of drilling holes in material from 1/2″ to 1-1/2″, at a 15 degree angle. It features a auto stop/start motor actuation by the pull/release of the handle, as well as a auto adjust clamping foot for varied material thicknesses. Overall size is 29″x18″x27″.

The JET JDP-17MF Floor Drill Press is a true woodworker’s drill press. With 16 speeds, it lets you choose the best speed for the job. It comes equipped with a quick release crank operated worktable, work light, X-pattern mounting grooves, depth stop, and adjustable tension spindle return spring which is ideal for repetitive drilling of the same depth. Features ... Read More

New Item! Powermatic  2014 variable speed bench lathe. Motor only requires a 115 volt single phase input while providing a consistent torque with 1 horse power, 230 volt, and 3 phase output using an inverter.Magnetic control box displays both digital speed and indexing and can be relocated for convenience and safety.Twenty four positive locking indexing position, displayed on the repositionable magnetic control box, simplifies the indexing process.Sliding headstock and removable tailstock make outboard turning easy, and theCast iron bed reduces motor vibration for decreased noise and added precision. Variable speeds from as low 15RPMs to as high as 3600RPMs, with the option of forward or reverse. With constant monitoring of the motor th... Read More

The JET® DC-1200VX features the exclusive Vortex Cone™ which improves chip separation to prevent clogging of the filter, and increases packing efficiency of the collector bag. The high air velocity (CFM) stands up to any competitive specifications, and the industrial controls are designed for years of durable use. Collection bags have a snap ring for fast installation and removal. Casters offer maneuverability within the shop. Eliminates premature filter clogging for sustained performance High air velocity (CFM) design stands up to any competitive specifications... Read More

Are you ready to get more from your dust collector? The Cyclone Dust Collector Collection from JET delivers the efficiency you’ve been waiting for. With a direct mount filter, a radio frequency remote control and a large collection bin these dust collectors take your shop’s capabilities to a new level. Upgrade to a JET Cyclone Dust Collector and experience The Power of Efficiency. Direct mounted filter eliminates inefficiencies from ridged flex hosing and bends Double paddle manual cleaning system quickly cleans the pleated filter ... Read More

he JET DC-1200VX features the exclusive Vortex Cone™ which improves chip separation to prevent clogging of the filter, and increases packing efficiency of the collector bag. The high air velocity (CFM) stands up to any competitive specifications, and the industrial controls are designed for years of durable use. Collection bags have a snap ring for fast installation and removal. Casters offer maneuverability within the shop. Eliminates premature filter clogging for sustained performance High air velocity (CFM) design stands up to any competitive specifications ... Read More

The Powermatic 15″ helical head planer is a great addition to any homeowner or industrial woodshop. It has 74 indexable insert cutterhead providing a quieter cut and finer finish compared to straight knives, giving a better result. Features: 74 four-sided inserts 3 V belts for maximum power Built in caster system Serrated infeed rollers Two speed gearbox Large cast iron table 4″ dust port Specs: Style (Type) Floor Type of Cutterhead Helical Cutterhead Speed (RPM) 4,500 Cutterhead Diameter (In.) 2-7/8 Number of Knives 74 Four Sided Carbide Helical Inserts Maximum Depth of Cut (In.) 3/16 Maximum Full Width Depth of Cut (In.) 1/8 Maxi... Read More

Used C.R Onsrud inverted pin router up for sale! These routers are production duty capable of producing template router applications every day, and will perform in heavy duty applications. Model: 3025 Serial: 30000404 04/2000 Year 5HP, 3PH, 230V 30″ Throat Phenolic Table Foot Pedal Spindle Control Flow Speed Control Spindle Bearings are in good condition Machine is in running condition, ready to work.  

Shipping: $425.00 The SawStop® Industrial Cabinet Saw is the definition of industrial grade. It is the heaviest, most powerful and highest quality 10″ cabinet saw available. The 5HP, 3ph, 230v configuration with a 52″ Industrial T-Glide Fence Assembly offers the durability, versatility, and the peace of mind only SawStop’s patented safety system can provide. 52-INCH T-GLIDE FENCE ASSEMBLY: The 52-inch T-Glide Fence & Rail are made of heavy-gauge steel for sure lockdown and reliably square cutting for years without deflection. STRENGTH & STABILITY: The Industrial Cabinet Saw is over 700 lbs of iron and steel – built for heavy-duty cycles with maxim... Read More

Engineered for continuous industrial applications, the Extrema ET-160 Shaper is a excellent machine for demanding applications. Features: 10 HP 3 spindle speeds: 5.5, 7.5 and 10K RPM Reversible Magnetic starter Precision fence assembly Table inserts Front access panel Spindle lock Micro adjust left and right positioning Spindle brake Emergency stop Optional digital readout Specs: Horsepower: 10HP Voltage: 230V or 460V Phase(s): 3PH Main Motor: 10 HP Spindle RPMs: 5.5 / 7.5 / 10K CFM Requirements: 750 Table Size: 46″ x 34″ Max Diameter: 12-3/8″ Spindle Travel: 6-1/2″ Incl... Read More

We have a clean Powermatic 221 20″ Industrial planer for sale. It features a segmented knife cutterhead, powered by a 7.5 horsepower Baldorthree phase motor, 230 Volt. 8″ x 20″ Capacity Mimimum of 1/8″ 4-1/8″ Cutting Circle 3600 SFM Segmented Infeed Roller Solid Outfeed Roller Solid Bed Roller 2,160lbs

Brand new Jet 14″ bandsaw. 1-3/4HP, 1PH, 115/230V. Heavy duty steel frame, large table with upgraded fence system, 13-1/2″ of resaw capacity with 13″ of height, and dual 4″ dust ports.Call for availability!

Used Nash chair back sander in overall good condition. Power is 5 HP,3 PH , 230, with a Baldor 1/3 HP feed drive motor. Height range 0-8″, and thickness range 0-3.5″. It has a 9″ contact drum and takes a belt size of 8″ X 110″.

Very Nice 36″ Bandsaw. Comes With A Powerfeed on the Table. Power is 3 Phase, 220 Volt Horsepower? At just under 9 feet tall and 4 feet wide at the base , this is a robust heavy duty machine.

Inventory Id# 30035 CUSTOMIZED Powermatic 225 BEAM Planer 24″x24″ capacity 15 H.P. 230 volt 3 phase belt drive HI-Speed spiral insert cutter head est 6000 RPM Dual 1.5 H.P. feed motors with a/c Inverter control with reversing feed Accurate DRO thickness read out will need additional guarding to comply with OSHA depending on  your operation VERY UNIQUE PLANER

The award winning PM2000B table saw sets a new standard for innovation with an array of patented features and massive body design. The cast iron tables are oversized, and the newly designed arbor lock lever is accessible from above the table top to eliminate the need for dual arbor wrenches. The quick-release riving knife design helps reduce the chance of kickback. The blade tilt scale features an integrated digital read out as well as adjustable angle indicators for repetitive bevel cuts. The newly designed integrated retractable hydraulic caster system mobilizes your table saw much higher than the previous model to assist when moving over thresholds. A wide stance, heavy-duty box trunnion and concave teeth on the trunnion gears promote... Read More

The PM1900 Dust Collector features the exclusive TurboCone™ which improves chip separation to prevent clogging of the filter, and increases packing efficiency of the collector bag. The canister filter offers superior filtering surface area over standard bags, and captures 98% of 2-micron particles. A digital timer can be set for up to 99 minutes, and an infrared sensor allows remote control operation. The all-metal duct improves rigidity and air flow. The clear collector bags are large capacity, which means less down-time changing them. Four swivel casters and conveniently located handles allow for easy mobility. ... Read More

Extrema offers a full range of wide belt sanders that were designed in the USA especially for the American market. All of our sanders are built using the highest quality components and construction methods such as mono-block construction, electrical controls, and Camozzi pneumatics. Exceess Series wide belt sanders use a 60″ belt. Theses machines have the same quality construction as our larger machines, but are affordable enough for even the smaller manufacturers. Truly an “excessive” amount of features for sander in its class. Horsepower: 25/20HP Voltage: 230V or 460V Phase(s): 3PH Belt Size: 37″ x 60″ CFM Requirement: 3600 Main Motor: 25 / 20 HP Feed Motor: 3 HP Elevation... Read More

The versatile Putsch® SVP 133 Space Save Series can be easily integrated into any workshop, regardless of budget. It is perfect for basic 4’X8′ sheets, while requiring less than 60 square feet of shop space. It is manufactured in Italy, and built with a heavy duty monolithic steel frame to ensure accurate horizontal and vertical cuts within a tenth of a millemeter (0.006″). Standard equipment is a 5HP, 3 PH, 230 volt URL motor, with a blade RPM of 6,360, horizontal repeat strip cutting device, aluminum support and lift-roller system, mid-grid retractable support shelf, and manual shifting grid. Max cutting height is 5’3″, max trimming height, 4’6″, max cutting length, 8’2″, and max cutting depth is 2.36″.... Read More

Extrema’s Titan XP double sided planer is a feature laden machine designed for industrial applications. Large power comes from the 25 horsepower top motor, and 20 horsepower bottom motor, three phase two thirty or four sixty volt. Carpet style feed system offers a 2 horsepower motor, giving you a feed speed from 20 to 65 feet per minute. Both cutterheads run at 6,000 RPM; The top cutterhead is accessed from the rear with the bottom head slides out giving easy access to change inserts. Minimum stock thickness is 3/8″, with a max thickness of 7″. Minimum CFM is 2900, and weight is 7550 pounds.

Say hello to JET’s 18″ scroll saw. Combining best-in-class features with innovation and thoughtful design to create the machine you’ve been waiting for. The best part about this saw is the blade change process. Our exclusive upper mechanism clamps and tensions the blade in one step. In addition to the upper mechanism, the toolless lower blade holder is removable and the table features a slot for the blade. The features don’t stop there: this saw offers eighteen inches of throat capacity and an arm that tilts forty five degrees right and thirty degrees right. This saw is designed to optimize your scrolling experience. From the variable speed range to a top lift, spring loaded arm it comes fully loaded with all the features you’d... Read More

Extrema’s Titan Series XP-126T comes in a 26″ width. The XP-126T is available with VECTOR Cutterhead, infeed roller, heavy duty internal drive system, and a PLC controler. Specs: Horsepower: 20 HP Voltage: 230V / 460V Phase(s): 3 PH Width: 26″ Main Horsepower: 20 HP Feed Horsepower: 1 HP Elevator Horsepower: 0.5 HP Max Thickness: 11.75″ Min Thickness: 0.375″ Max Cut: 0.375″ Min Length: 10.5″ Cutterhead RPM: 6000 Feed Speed: 20-75 ft/min CFM Requirements: 1100 Thickness Adjustment: PLC Controller Bed Roller Adjustment: External Power Bed Rollers: Top and Bottom AMPS (230V/460V): 52A / 26A Weight: 2675 lbs... Read More

For sale is a clean Ritter R813 Horizontal 13 Spindle Boring Machine. Perfect for the shutter industry, or anywhere a job calls for multiple horizontal holes. Model: R813 Serial: 117 230V 3PH, 60Hz Mfg: 4/22/99 13 spindle drill operation, 6 lefts, 7 rights Dual Pneumatic clamps Foot Pedal Activation Approx 1800lbs Contact for a shipping quote

Now featuring ArmorGlide Technology that is low-friction and rust-resistant, the Powermatic PJ-882HHT 8-Inch Parallelogram Jointer offers performance and value in a machine loaded with features. The cutterhead is a helical design with 54 four-sided knife inserts. These inserts produce a superior finish and much quieter operation than conventional cutterheads, and the inserts do not require adjustment once installed.The jointer has an extra long 82-inch bed for better work support and is equipped with an innovative single handwheel design that tilts the fence in and out with positive stops at +/-45 and 90 degrees. A non-mar insert in the fence contacts the table to avoid scratching the surface during adjustments. The parallelogram design ... Read More

The Extrema XS-2P53 is a heavy duty wide belt sander tha is the largest of their industrial line of wide belt sanders. It offers high quality components such as mono-block construction, Telemecaique electrical controls, and Camozzi pneumatic’s. Features: Four Post Table Design 75″ Belt Length Over thickness safety device Infeed bed rollers Digital thickness controller Individual amp meters Disc brakes on sanding heads Telemecaique electrics Camozzi pneumatics Variable speed drive system Specs: Horsepower: 30/30 HP Voltage: 230V or 460V Phase(s): 3PH Belt Size: 52″ x 75″ CFM Requirement: 4800 Main Motor: 30 / 30 HP ... Read More

Item No. Distance Between Centers Overall Length Swing Over Bed 2436 36″ 60″ 24″ 2416 16″ 40″ 24″ 2036 36″ 60″ 20″ 2016 16″ 40″ 20″ AC Electronic Variable Drive 0 – 3000 RPM with Full Speed Reverse – Drive packages are fully electronic with speed from 0 – 3000 RPM – 1.5, 2 & 3 Horse Power motors are available. Excellent torque is available at as low as 30 RPM with brute force available at as little as 100 RPM – Speed ranges are 20 – 800/190 – 1900/305 – 3050. Changing range is easy and can be completed in under 1 minute – Drive motor is mounted... Read More

The JBOS-5 Benchtop Spindle Sander has a 1/2HP motor, and a large 14-1/2” tilting table. A heavy-duty worm gear system provides one-inch oscillating action, which prolongs sleeve life and helps prevent burnishing of the workpiece. Four inserts are provided, and 5 spindles with sanding sleeves. FEATURES 1″ oscillating action reduces friction heat to protect wood and prolong sleeve life Main spindle support runs on precision ball bearings and is oscillated by a heavy-duty worm and gear mechanism for consistent performance Oscillation gears run in a sealed lubricated box to prolong their life and durability Table tilts to 45° to accommodate bevel sanding projects Removable on/off safety switch preve... Read More

The New JET 13” Benchtop planer delivers the power and efficiency that woodworkers demand in the shop. The JET 13″ Planer produces a smooth and consistent cut surface thanks to its Helical Style Cutter head with 6 rows of 26 individual quick change inserts which can be easily rotated or replaced if damaged or worn. This helical style cutter head design helps reduce noise as its powerful 2HP 15 Amp Motor is turning at an impressive 10,000 RPM. Features include a rugged 4 post design, adjustable folding tables, 2 infeed speeds and a sturdy Cast Iron base which helps reduce snipe. Stock Number ... Read More

The JET ProShop Table Saw offers features you expect from a high-end cabinet saw, in the compact design of a contractor-style machine. The redesigned transparent blade guard has independent leaves, and the quick release riving knife reduces chance of kickback. A low profile riving knife is included for non-through cuts. The exclusive ProShop fence system is available in 30” or 52” rip capacity. Convenient, magnetic paddle switch for the safest operation possible CSA Certified Improved dust shroud around blade for grea... Read More

One of the largest oscillating edge sanders on the market, the ES-9138 lets you create smooth, well-fitted cabinets, doors, and flooring. The steel base and cast iron table ensure stability. Accepts 9” x 138.5” belts, a common size. Long, wide belt will last longer and run cooler than smaller belts. Belt turns 3,000 rpm. 3 hp 220-volt single-phase motor powers the belt and runs the gearbox to control the oscillating action. 24 oscillations per minute produce a smoother finish, use the entire belt face, and lengthen belt life. 11¾” x 48” table can accommodate even the largest of pieces. Massive cast iron table gives you a true, level surface over many years of heavy production. Tab... Read More

The new JET JMS-12 dual bevel sliding compound miter saw is a proffesional saw that will efficiently cut miters,bevels,straights, and compounds, with prcision and accuracy, making it a excellent shop saw or jobsite saw. FEATURES: Dual bevel capability with up front controls Enclosed linear bearings Durable compact die cast aluminum construction Heavy duty 15 amp motor Ergonomic, D-shaped, ambidextrous, rubber grip handle for maximum control Razor thin high visibility red laser LED light Miter detent override Adjustable left and right fence and extension tables Dust port with dust bag and 2-1/2” adaptor 5 second motor brake SPECIFICATIONS: 15 amp... Read More

Shipping: $325.00 The Professional Cabinet Saw is SawStop’s top selling cabinet saw, offering unmatched fit and finish and best-in class cutting performance. 30-INCH PREMIUM FENCE ASSEMBLY: This aluminum fence assembly provides smooth operation and precise measurement. UNMATCHED QUALITY: The trunnion and arbor are built for precision, strength and stability. The gas piston elevation delivers smooth and easy adjustability. Table flatness is measured diagonally at 0. 010” maximum gap. DUST COLLECTION: 99% dust collection is delivered above the table with the available dust collection blade guard (Model # TSG-DC, sold separately), and below the table with ... Read More

The Extrema Pro series 16″ jointer is designed for continuous use in a production environment while giving you a clean straight finish. Standard features include manual brake with shutoff,parallelogram bed design, heat treated infeed and outfeed tables, positive stops at 45 and 90 degrees, and independent bed adjustment. Specs: Horsepower: 5HP Voltage: 230V Phase(s): 3PH Main Motor: 5 HP for 3-Phase Width: 16″ Bed Length: 100″ Infeed Bed: 52-1/2″ Outfeed Bed: 45-1/4″ Infeed Adjustment: 3/8″ Outfeed Adjustment: 1/8″ Tilt Range: 0° – 45° AMPS @ 230V: 13 Weight: 1605 lbs

NEW ITEM! Powermatic PM2014 variable speed lathe with stand. Motor only requires a 115 volt single phase input while providing a consistent torque with 1 horse power, 230 volt, and 3 phase output using an inverter.Most range of height in the Powermatic family. Adjust centerline to floor from 34 inches to 46 inches for maximum control and comfort.Magnetic control box displays both digital speed and indexing and can be relocated for convenience and safetyTwenty four positive locking indexing position, displayed on the repositionable magnetic control box, simplifies the indexing processSliding headstock and removable tailstock make outboard turning easyCast iron bed reduces motor vibration for decreased noise and added precision.Varia... Read More

Used Max HD-237 24″ heavy duty industrial disc sander. Machine was just pulled from service, and is in excellent running condition. It was only replaced because the company bought a smaller new machine because they don’t need the size. Make: Max Model; HD-237 3HP, 3PH, 230/460V 1170RPM Rack and Pinion Table Elevation Rack and Pinion Table Bevel Adjustment Heavy Duty Cast Iron Base, Column, and Table Magnetic Start Stop Switch Dust Blower USA made in San Jose CA! Comes with Extra Sandpaper!

Product Details If you’re looking for the ultimate machine to build face-fames, this is it. The DK3100 contains three spindles that allow you to drill two pocket holes across rails of varying widths in just one machine cycle. Best of all, the DK3100 can also be quickly changed to drill a single pocket hole, like our DK1100 series, by simply removing a drill bit. If you’re serious about face-frame production, the DK3100 is the machine that will deliver real performance to your shop and profits to your bottom line. The DK3100 not only drills two pocket holes in one cycle, it also gives you options for spacing the holes. You can set the drill spindles at 3/4″, 1″, and 13/4″ on center, perfect for today’s... Read More

Heavy Duty ice scrapers for sale, custom made in our machine shop,in Blue Ball Pennsylvania. All steel construction, with a 8″xl10″ scraper blade, and a48″ handle,giving you 8 pounds of ice breaking power. Wholesale pricing 5+. Link to online purchasing: http://www.ebay.com/itm/333407037808

Utility Pro Hi-vis softshell jacket. Class 3 ANSI certified. Different sizes available.

Hi-vis safety vest, UHV312 , class 3 ANSI certified . L/XL sizes available.

Utility Pro hi-vis pants. Waterproof, class 3, ANSI certified. Different sizes available.

Utility Pro Hi-vis UHV821 3 in 1 bomber jacket. Removable liner, class 3 ANSI certified. Different sizes available.

Wilton is  on a never-ending journey to create the highest quality, most indestructible tools on the market. On this journey they’ve managed to design and file patents for the world’s most durable sledge hammer with Unbreakable® Handle Technology, revolutionary design, and engineered no-slip rubber grip. With the Wilton B.A.S.H® backed by their $1,000 Guarantee, they put their money where their mouth is. Ergonomic Handle – shaped and thickened for improved comfort and less vibration Lanyard Hole – Safely secure hammer to wrist or stationary obj... Read More

Air Mate 2HP, 1PH, 115 volt, dual tank four gallon portable air compressor. Max PSI is 125: Used but in good condition.

Roto-Phase 20HP phase convertor for sale. 1PH 230V input, converts to 3PH 230V output. Can run up to 60HP combined Fully cleaned and tested, runs good.

Jenny 80 gallon vertical tank industrial air compressor, model W5B-80. Specs: 5 HP 1 PH, 230V UL Electric Motor Two Stage W Pump Features: Heavy-duty single or two stage cast iron compressor pump – Made in Somerset, PA USA Splash lubricated Belt driven with a large flywheel for extra cooling and easier start-up Each unit is filled with Jenny Ultimate Blue Synthetic Compressor Pump Oil Directional air shroud for reduced pump temperatures Totally enclosed heavy-duty belt guard Tanks are powder coated and ASME certified 60 gallon tanks and larger are ASME National Board certified Protectively mounted fittings Manual tank drain(s) Larg... Read More

This is a used motor in good condition. Specs. are: 1-1/2 HP, 3 phase, 230 volt, 1725 RPM, and 7/8″ shaft.

Teco-Westinghouse 30HP, 3Ph, 230/460 V motor. 1800 rpm, 70amp, Frame 286T. Only ran once! Like new.

Metabo 5″ angle grinder. Runs at 11000 RPM, has a automatic safety clutch, quick wheel change, paddle switch, and two second brake. CALL FOR AVAILABILITY!

Metabo 5″ performance grinder is a powerful and robust angle grinder with speed regulation and ergonomic soft handle for fatigue-free working, especially over your head Features: Powerful motor with good overload capacity Vario-Tacho-Constamatic (VTC)-Full Wave Electronics with Thumbwheel: for working at customized speeds to suit the application material and speeds that remain almost constant, even under load Tool-free adjustable guard; twist-proof Electronic safety shutdown of the motor reduces kickback if the disc stops unexpectedly- for high user protection Electronic soft start for smooth start-up Restart protection after power failure Auto-stop carbon brushes to protect the motor... Read More

The Power Port LED-750 work light is a powerful and lightweight addition to any garage, toolbox, or work vehicle, providing up to 750 lumens to illuminate any dark spaces. It features a impact resistant design, polycarbonate lens, aluminum housing, and non-slip rubberized grip. It has a 3.7 volt, 4000 mAh, Li-Hd rechargeable battery, giving you 3 hours of runtime on high (750 lumens), or seven hours of runtime on low (300 lumens). Acessories include 360 degree swivel hook, clip on magnetic base, USB wall adaptor, and micro USB charging cable.

The Power Port LED-1000 work light is a powerful and lightweight addition to any garage, toolbox, or work vehicle, providing up to 1000 lumens to illuminate any dark spaces. It features a impact resistant design, polycarbonate lens, aluminum housing, and non-slip rubberized grip. It has a 3.7 volt, 4000 mAh, Li-Hd rechargeable battery, giving you 2 hours of runtime on high (1000 lumens), or four hours of runtime on low (500 lumens). Acessories include 360 degree swivel hook, clip on magnetic base, USB wall adaptor, and micro USB charging cable.

Powerful 15A / 3-1/4hp electronically-controlled motor with variable speed, soft start and safety switch. Features a removable fixed base with a depth adjustment range of 3-1/8″ and a max cutting diameter of 3″. Effective dust extraction. Includes guide fence, 2 x collet wrenches, 1/2″ collet and guide bush adapter. Product Features 15A / 3-1/4hp soft-start motor with constant speed under load for powering through the toughest timbers with a consistent finish 10,000 – 21,000min-1... Read More